Accessories

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. CLASS II SELV Dimensions: 195 x 43 x 30,2 mm

S.2401
POWER SUPPLY NOT DIMMABLE 60W 230Vac/24Vdc IP20

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. CLASS II SELV Dimensions: 225 x 43 x 29,8 mm

S.2402
POWER SUPPLY NOT DIMMABLE IN BOX 60W 230Vac/24Vdc IP55 MAX 5 OUTPUTS

Dimensions: 260 x 240 x 100 mm.
Cable IN: 2 with cable glands PG11
Cable OUT: 5 with cable glands PG11
IP55 CLASS II SELV The Total power of all connected luminaires may not be higher than the power of the driver.

S.2403
POWER SUPPLY NOT DIMMABLE 100W 230Vac/24Vdc IP20

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. CLASS II SELV Dimensions: 295 x 43 x 29,8 mm

S.2404
POWER SUPPLY NOT DIMMABLE IN BOX 90W 230Vac/24Vdc IP55 MAX 5 OUTPUTS

S.2405
POWER SUPPLY NOT DIMMABLE 60W 230Vac/24Vdc IP67

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. CLASS II SELV Dimensions: 150 x 53 x 21 mm

S.2406
POWER SUPPLY NOT DIMMABLE 90W 230Vac/24Vdc IP67

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. CLASS II SELV Dimensions: 171 x 63 x 37,5 mm

S.2407
POWER SUPPLY NOT DIMMABLE 14,4W 230Vac/24Vdc IP67

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV Dimensions: 79 x 38 x 25 mm.

S.2433
POWER SUPPLY NOT DIMMABLE 36W 230Vac/24Vdc IP67

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV Dimensions: 120 x 38 x 25 mm.

S.2445
POWER SUPPLY NOT DIMMABLE 120W 230Vac/24Vdc IP67

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. CLASS II SELV Dimensions: 191 x 63 x 37,5 mm

S.2446
POWER SUPPLY NOT DIMMABLE 320W 230Vac/24Vdc IP67

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. CLASS I SELV Dimensions: 252 x 90 x 43 mm

S.3400
POWER SUPPLY NOT DIMMABLE 10W 230Vac/24Vdc IP20

In: 240V Alternate Current
Out: 24V Direct Current.
The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions: 120 x 35 x 20 mm.

S.3401
POWER SUPPLY NOT DIMMABLE IN BOX 10W 230Vac/24Vdc IP55 MAX 6 OUTPUTS

(Electronic power supply included)
Dimensions: 230 x 210 x 80 mm.
Cable IN: 2 with cable glands PG11
Cable OUT: 6 with cable glands PG11
IP55 CLASS II The Total power of all connected luminaires may not be higher than the power of the driver.

S.3425
POWER SUPPLY NOT DIMMABLE 230Vac/24Vdc 8W IP54

It can be housed directly in the recessed box of MINISKILL round, square and vertical flush versions. (To be wired into the recessed box ensuring adequate IP protection). Dimensions : 51mm x 31mm x h 21mm

S.3664
JUNCTION BOX WITH NOT DIMMABLE POWER SUPPLY 35W 240V/24Vdc

IP65 power supply for: N°4 Micropool LED* o N°1 Minipool LED o N°1 Pool LED maximum load capacity 500Kg Dimensions 200mmx200mmx220mm *= require 2 x S.3670 additional cable gland

S.3665
JUNCTION BOX WITH NOT DIMMABLE POWER SUPPLY 90W 240V/24Vdc

IP65 power supply for: N°5 Micropool LED** o N°4 Minipool LED* o N°2 Pool LED maximum load capacity 500Kg Dimensions 300mmx300mmx230mm ** = require 3 x S.3670 additional cable gland * = require 2 x S.3670 additional cable gland

Remoted power supply 24v dali dimmable

S.2415
POWER SUPPLY DIMMABLE 230Vac/24Vdc 24W 244Hz IP67

Dimmable DALI for monochromatic LED 24W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV PWM Frequency : 244Hz Dimensions 185 x 35x 33mm

S.2416
POWER SUPPLY DIMMABLE 230Vac/24Vdc 75W 244Hz IP67

Dimmable DALI 2 for monochromatic LED 75W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV PWM Frequency : 244Hz Dimensions 280 x 40x 28mm

S.2419
POWER SUPPLY DIMMABLE DALI2, PUSH DIM 36W 230Vac/24Vdc 3,6KHz IP20

Dimmable DALI2, PUSH DIM for monochromatic LED 35W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP20 CLASS II SELV Dimensions 210mmx43mmx30mm PWM Frequency : <3,6KHz

S.2421
POWER SUPPLY DIMMABLE DALI, PUSH DIM e DSI 60W 230Vac/24Vdc 1KHz IP20

Dimmable DALI, PUSH DIM, DSI for monochromatic LED 60W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP20 CLASS II SELV PWM Frequency : ~1KHz Dimensions 225 x 43x 29,8mm NB: not suitable for Family products NANOLED STAINLESS-STEEL

S.2423
BOX WITH DIMMABLE POWER SUPPLY DALI2, 1-10v e PUSH-DIM 60W 230Vac/24Vdc 2kHz IP55 MAX 5 OUTPUTS

60W 230Vac/24Vdc Dimensions 260mmx240mmx100mm PWM Frequency : 2kHz IP55 SELV CLASS II NB: not suitable for Family products NANOLED STAINLESS STEEL

S.2425
BOX WITH DIMMABLE POWER SUPPLY DALI, 1-10v e PUSH-DIM 90W 230Vac/24Vdc 2kHz IP55 MAX 5 OUTPUTS

90W 230Vac/24Vdc Dimensions 260mmx240mmx100mm PWM Frequency : 2kHz IP55 SELV CLASS II NB: not suitable for Family products NANOLED STAINLESS STEEL

S.2426
POWER SUPPLY DIMMABLE DALI 2 120W 230Vac/24Vdc 2,5KHz IP67

Dimmable DALI 2 for monochromatic LED 120W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV PWM Frequency : 2,5KHz Dimensions 191 x 63x 37,5mm NB: not suitable for Family products NANOLED STAINLESS STEEL

S.2429
POWER SUPPLY DIMMABLE DALI2, PUSH DIM 75W 230Vac/24Vdc 3,6KHz IP20

Dimmable DALI2, PUSH DIM for monochromatic LED 75W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP20 CLASS II SELV Dimensions 293mmx43mmx30mm PWM Frequency : <3,6KHz

S.2441
POWER SUPPLY DIMMABLE DALI, PUSH DIM, 0-10V, 1-10V 230Vac/24Vdc 24W 244Hz IP20

Dimmable DALI, PUSH DIM, 0-10V, 1-10V for monochromatic LED 24W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. PWM Frequency : 244Hz Dimensions 164mm x38mm x24,5mm IP20 CLASS II SELV

S.2442
POWER SUPPLY DIMMABLE DALI2, PUSH DIM, 0-10V, 1-10V 230Vac/24Vdc 75W 244Hz IP20

Dimmable DALI2, PUSH DIM, 0-10V, 1-10V for monochromatic LED 75W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP20 CLASS II SELV PWM Frequency : 244Hz Dimensions 280mmx40mmx29mm

S.2447
POWER SUPPLY DALI 200W 230Vac/24Vdc

Power supply for monochromatic LED 200W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV Dimensions 195x68x39mm

S.2449
POWER SUPPLY DIMMABLE DALI2, PUSH DIM 100W 230Vac/24Vdc 3,6KHz IP20

Dimmable DALI2, PUSH DIM for monochromatic LED 100W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP20 CLASS II SELV Dimensions 293mmx43mmx30mm PWM Frequency : <3,6KHz

S.9099
Master Interface

Combined with a common 60W 24V On-Off power supply, it controls Flower ZOOM 60 products with DALI single control up to a maximum power of 60W total for each Highlighter rod. Only individualcontrolled Flower ZOOM 60 products should be used in this configuration. A maximum of n.5 Flower ZOOM 60 Individual controll can be installed on one Highlighter, regardless of its length. These can be controlled independently of each other and of the Highlighter lighting rod thanks to the DALI protocol. Each Highlighter lighting rod, used for the installation of the single control products, needs n.1 master interface accessory (S.9099) for DALI control.

Remoted power supply 24v 1-10v dimmable

S.2427
POWER SUPPLY DIMMABLE 1-10V 60W 230Vac/24Vdc 1,47KHz IP67

Dimmable 1-10V for monochromatic LED 60W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV PWM Frequency : 1,47KHz Dimensions 150x53x35mm NB: not suitable for Family products NANOLED STAINLESS-STEEL

S.2428
POWER SUPPLY DIMMABLE 1-10V 90W 230Vac/24Vdc 1,47KHz IP67

Dimmable 1-10V for monochromatic LED 90W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV PWM Frequency : 1,47KHz Dimensions 171 x 63x 37,5mm NB: not suitable for Family products NANOLED STAINLESS-STEEL

Remoted power supply 48v not dimmable

S.2448
POWER SUPPLY ON-OFF 31W 230Vac/48Vdc IP67

Power supply for monochromatic LED 31W 240V/48Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV Dimensions 120x38x25mm

Remoted power supply 24v pushdim dimmable

S.2424
POWER SUPPLY DIMMABLE 1-10V, PUSH DIM 60W 230Vac/24Vdc 244Hz IP20

Dimmable 1-10V, PUSH DIM for monochromatic LED 60W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP20 CLASS II SELV PWM Frequency : 244Hz Dimensions 125 x 82x 29mm

Remoted power supply Current not dimmable

S.2408
POWER SUPPLY NOT DIMMABLE MULTI-POWER 230V/350mA-1050mA 57,8W IP67

Maximum power consumption 57,8W Dimensions 185mmx35mmx35mm IP67 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2409
POWER SUPPLY NOT DIMMABLE 230V/1000mA 14W IP67

230V/1000mA Maximum power consumption: 14W Dimensions 70mmx38mmx24mm IP67 SELV CLASS II Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2430
POWER SUPPLY NOT DIMMABLE MULTI-POWER 230V/250mA-700mA 20W oppure 24Vdc 16W IP20

MULTI-POWER SUPPLY 230V/250mA-700mA Maximum power consumption 20W or 16W 230Vac/24Vdc Dimensions 110mmx50mmx20mm IP20 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2431
POWER SUPPLY NOT DIMMABLE MULTI-POWER 230V/350mA-1050mA 39W IP20

Maximum power consumption 39W Dimensions 130mmx67mmx21mm IP20 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2432
POWER SUPPLY NOT DIMMABLE MULTI-POWER 230V/350mA-1050mA 50W IP20

Maximum power consumption 50W Dimensions 130mmx67mmx21mm IP20 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2434
POWER SUPPLY NOT DIMMABLE MULTI-POWER 230V/200mA-700mA 20W IP67

Maximum power consumption 20W Dimensions 120mmx38mmx25mm IP67 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2435
POWER SUPPLY NOT DIMMABLE IN BOX IP67 230V/250mA-700mA 20W o 230Vac/24Vdc 16W IP67

MULTI-POWER SUPPLY 230V/250mA-700mA Maximum power consumption 20W or 16W 230Vac/24Vdc Dimensions 175,5mmx86,5mmx43mm IP67 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2436
POWER SUPPLY NOT DIMMABLE MULTI-POWER 230V/350mA-1050mA 50W IN BOX IP55 MAX 5 OUTPUTS

Maximum power consumption 50W Dimensions 260mmx260mmx100mm IP55 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.3424
POWER SUPPLY NOT DIMMABLE 230V/1200mA 6W IP20

Power consumption 6W Dimensions 57mmx31mmx21mm IP20 Must be installed in protect area, suitable for 1 device. Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

Remoted power supply Current dali dimmable

S.2410
POWER SUPPLY DALI2 230V/350-1050mA 57,8W IP67

230V/350-1050mA Maximum power consumption: 57,8W Dimensions 185mmx35mmx35mm IP67 SELV CLASS II Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2411
POWER SUPPLY 0/1-10V 230V/700mA 17W o 230V/24V 15W IP68

230V/700mA Maximum power consumption: 17W or 230V/24V Frequency PWM : 240Hz Maximum power consumption: 15W Dimensions 121mmx53mmx26mm IP68 SELV CLASS II Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2413
POWER SUPPLY DALI / 1-10V / PUSH MULTI-POWER 230V/250mA-700mA IP20

230V/250mA-700mA Maximum power consumption: @250mA 28W, … ,@700mA 60W. Dimensions 124mmx79mmx22mm IP20 Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2414
POWER SUPPLY 0/1-10V, DALI2 230V/1200mA 60W IP68

230V/1200mA Maximum power consumption: 60W (Vout min 10V - Vout max 50V) Dimensions 135mmx80mmx31mm IP68 SELV CLASS II Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2437
POWER SUPPLY MULTI-POWER 230V/350mA-1050mA DALI DIMMABLE, 1-10V, PUSH DIM IN BOX IP55 60W MAX 5 OUTPUTS

230V/350mA-1050mA Maximum power consumption: 60W Dimensions 260mmx260mmx100mm IP55 CLASS II SELV 120V Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2438
POWER SUPPLY 230V/250mA-700mA 20W o 230Vac/24Vdc 16W 240Hz DALI DIMMABLE IN BOX IP67

DALI DIMMABLE MULTI-POWER SUPPLY 230V/250mA-700mA Maximum power consumption: 20W or 16W 230Vac/24Vdc Dimensions 175,5mmx86,5mmx43mm PWM Frequency : 240Hz IP67 CLASS II SELV NB: not suitable for Family products NANOLED STAINLESS STEEL Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2443
POWER SUPPLY MULTI-POWER 230V/100mA-800mA DALI2 DIMMABLE, PUSH DIM IN BOX IP67 23W

230V/100mA-800mA Maximum power consumption: 23W Dimensions 175,5mmx86,5mmx43mm IP67 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2444
POWER SUPPLY MULTI-POWER 230V/700mA-1050mA DALI2, PUSH DIM IN BOX IP67 35W

230V/700mA-1050mA Maximum power consumption: 35W Dimensions 175,5mmx86,5mmx43mm IP67 CLASS II SELV Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.3427
POWER SUPPLY Dali, 1-10V, PUSH MULTI-POWER 230V/350mA-1050mA IP20

Dali, Dimmable 1-10V, PUSH BOTTON 230V/350mA-1050mA Maximum power consumption: @350mA 25W, @500mA 35W, @550mA 39W, @650mA 46W, @700-1050mA 50W. Dimensions 125mmx80mmx20mm IP20 SELV 120V Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

Remoted power supply Current phase-cut dimmable

S.2412
POWER SUPPLY 1-10V / PUSH MULTI-POWER 230V/250mA-900mA IP20

230V/250mA-900mA Maximum power consumption: @250mA 13W, … ,@900mA 20W. Dimensions 136mmx42mmx24mm IP20 Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2417
POWER SUPPLY DALI2 / PUSH MULTI-POWER 230V/100mA-800mA IP20

230V/100mA-800mA Maximum power consumption: @100mA 5,8W, ..., @800mA 23,5W. Dimensions 110mmx40mmx21mm IP20 Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.2418
POWER SUPPLY DALI2 / PUSH MULTI-POWER 230V/700mA-1050mA IP20

230V/700mA-1050mA Maximum power consumption: @700mA 28W, …, @1050mA 34,7W. Dimensions 136mmx42mmx24mm IP20 Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.3426
POWER SUPPLY DALI MULTI-POWER 230V/250mA-700mA o 230V/24V 16W 240Hz IP20

230V/250mA-700mA or 230V/24V Maximum power consumption: @250mA 10W, @350mA 15W, @400mA 17W, @450mA 19W, @500-700mA 20W. @24V 16W PWM Frequency : 240Hz Dimensions 110mmx50mmx20mm IP20 NB: not suitable for Family products NANOLED STAINLESS STEEL Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

Remoted power supply Current 1-10v dimmable

S.2439
POWER SUPPLY 230V/250mA-700mA 20W o 230Vac/24Vdc 16W 240Hz DIMMABLE 1-10V, PUSH DIM IN BOX IP67

1-10V, PUSH DIM DIMMABLE MULTI-POWER SUPPLY 230V/250mA-900mA Maximum power consumption: 20W or 16W 230Vac/24Vdc Dimensions 175,5mmx86,5mmx43mm PWM Frequency : 240Hz IP67 CLASS II SELV NB: not suitable for Family products NANOLED STAINLESS STEEL Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

S.3423
POWER SUPPLY MULTI-POWER 230V/350mA-1050mA IP20

Dimmable 1-10V, PUSH BOTTON Maximum power consumption: @350mA 15W, @500mA 21W, @550mA 23W, @650mA 27W, @700mA 29W, @750mA 31W, @850mA 35W, @900mA 37W, @1050mA 39W Dimensions 130mmx67mmx21mm IP20 For easy installation we recommend the wiring of maximum 2 devices in series to each power supply. Warning!!! Always check the minimum Forward voltage (Vf min) of the fixtures that will be connected to this driver.

Remoted power supply 24v tunable white

S.2470
POWER SUPPLY DMX 75W 230Vac/24Vdc IP20 TUNABLE WHITE

remote power supply DMX for TUNABLE WHITE LED 75W 240V/24V PWM The Total power of all connected luminaires may not be higher than the power of the driver. IP20 CLASS II SELV Dimensions 295 x 43x 29,8mm

S.2475
POWER SUPPLY DIMMABLE 75W 230Vac/24Vdc IP20 TUNABLE WHITE DALI DT8

Dimmable DALI DT8, PUSH DIM for TUNABLE WHITE LED 75W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP20 CLASS II SELV Dimensions 295 x 43x 29,8mm

S.2480
POWER SUPPLY TUNABLE WHITE IP55 60W 230V/24V PWM DMX MAX 5 OUTPUTS

IP55 box with 60W power supply 240V/24V PWM controlled by DMX protocol. The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 260mmx260mmx100mm

S.2485
POWER SUPPLY TUNABLE WHITE IP55 60W 230V/24V DALI DT6 MAX 5 OUTPUTS

IP55 box with 60W power supply 240V/24V PWM dimmable DALI DT6 ( operating mode BALANCE & DIM). The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 260mmx260mmx100mm

S.2486
POWER SUPPLY TUNABLE WHITE IP55 60W 230V/24V DALI DT8 MAX 5 OUTPUTS

IP55 box with 60W power supply 240V/24V PWM dimmable DALI DT8 ( operating mode BALANCE & DIM). The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 260mmx260mmx100mm

Remoted power supply Current tunable white

S.3414
POWER SUPPLY TUNABLE WHITE IP67 44,1W 230V/1050mA DALI DT8

IP67 box with 44,1W power supply 230V/1050mA dimmable DALI DT8 (operating mode BALANCE & DIM). The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 175,5mmx86,5mmx43mm IP67

Remoted power supply 24v rgbw

S.2440
POWER SUPPLY RGBW IP55 320W 230V/24V PWM DMX MAX 10 OUTPUTS

IP55 box with 320W power supply 240V/24V PWM controlled by DMX protocol. The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 316mm x300mm x128mm

S.3411
POWER SUPPLY RGBW IP55 60W 230V/24V PWM DMX MAX 5 OUTPUTS

IP55 box with 60W power supply 240V/24V PWM controlled by DMX protocol. The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 260mmx260mmx100mm

S.3413
POWER SUPPLY IP55 RGBW 90W 230V/24V PWM DMX MAX 5 OUTPUTS

IP55 box with 90W power supply 240V/24V PWM controlled by DMX protocol. The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 260mmx260mmx100mm

S.3415
POWER SUPPLY RGBW IP55 60W 230V/24V PWM DALI DT6 MAX 5 OUTPUTS

IP55 box with 60W power supply 240V/24V PWM controlled by DALI DT6 protocol. The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 260mmx260mmx100mm

S.3416
POWER SUPPLY RGBW IP55 90W 230V/24V PWM DALI DT6 MAX 5 OUTPUTS

IP55 box with 90W power supply 240V/24V PWM controlled by DALI DT6 protocol. The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 260mmx260mmx100mm

S.3417
POWER SUPPLY RGBW IP55 320W 230V/24V PWM DALI DT6 MAX 10 OUTPUTS

IP55 box with 320W power supply 240V/24V PWM controlled by DALI DT6 protocol. The Total power of all connected luminaires may not be higher than the power of the driver. Dimensions 326mmx300mmx128mm

S.3640
JUNCTION BOX WITH RGBW POWER SUPPLY 35W 240V/24V PWM DALI

IP65 power supply for:N°4 Micropool LED RGBW** o N°2 Minipool LED RGBW* o N°1 Pool LED RGBW DALI addresses:4 Controlled by DALI DT6 protocol maximum load capacity 500Kg Dimensions 200mmx200mmx220mm * = require 1 x S.3670 additional cable gland ** = require 2 x S.3670 additional cable gland

S.3642
JUNCTION BOX WITH RGBW POWER SUPPLY 90W 240V/24V PWM DALI

IP65 power supply for: N°5 Micropool LED RGBW*** or N°5 Minipool LED RGBW*** or N°2 Pool LED RGBW DALI addresses:4 Controlled by DALI DT6 protocol maximum load capacity 500Kg Dimensions 300mmx300mmx230mm *** = require 3 x S.3670 additional cable gland

S.3667
JUNCTION BOX WITH RGBW POWER SUPPLY 90W 240V/24V PWM DMX

IP65 power supply for: N°4 Micropool LED RGBW** or N°4 Minipool LED RGBW** or N°2 Pool LED RGBW maximum load capacity 500Kg Dimensions 300mmx300mmx230mm ** = require 2 x S.3670 additional cable gland

S.3668
JUNCTION BOX WITH RGBW POWER SUPPLY 35W 240V/24V PWM DMX

IP65 power supply for:N°3 Micropool LED RGBW o N°2 Minipool LED RGBW o N°1 Pool LED RGBW maximum load capacity 500Kg Dimensions 200mmx200mmx220mm

Surge protection device

S.2498
SURGE PROTECTION DEVICE 10kV CLASS I

Compatible with all lighting fixtures classified under electrical Protection Class I Rated voltage 230-277V SPD type 2+3 Max Surge Protection 10kV IP67

S.2499
SURGE PROTECTION DEVICE 10kV CLASS II

Compatible with all lighting fixtures and electronic ballast accessories classified under electrical Protection Class II Rated voltage 230-277V SPD type 2+3 Max Surge Protection 10kV IP67

Junction box

S.3660
JUNCTION BOX IP65*

Junction box with cable glands for 3 cables IN (possibility of 3 more cables IN with S.3670 accessories) Maximum load capacity 500Kg Dimensions 300mmx300mmx230mm

Controller 24v dali dimmable

S.2415
POWER SUPPLY DIMMABLE 230Vac/24Vdc 24W 244Hz IP67

S.2416
POWER SUPPLY DIMMABLE 230Vac/24Vdc 75W 244Hz IP67

S.2419
POWER SUPPLY DIMMABLE DALI2, PUSH DIM 36W 230Vac/24Vdc 3,6KHz IP20

S.2421
POWER SUPPLY DIMMABLE DALI, PUSH DIM e DSI 60W 230Vac/24Vdc 1KHz IP20

S.2423
BOX WITH DIMMABLE POWER SUPPLY DALI2, 1-10v e PUSH-DIM 60W 230Vac/24Vdc 2kHz IP55 MAX 5 OUTPUTS

60W 230Vac/24Vdc Dimensions 260mmx240mmx100mm PWM Frequency : 2kHz IP55 SELV CLASS II NB: not suitable for Family products NANOLED STAINLESS STEEL

S.2425
BOX WITH DIMMABLE POWER SUPPLY DALI, 1-10v e PUSH-DIM 90W 230Vac/24Vdc 2kHz IP55 MAX 5 OUTPUTS

90W 230Vac/24Vdc Dimensions 260mmx240mmx100mm PWM Frequency : 2kHz IP55 SELV CLASS II NB: not suitable for Family products NANOLED STAINLESS STEEL

S.2426
POWER SUPPLY DIMMABLE DALI 2 120W 230Vac/24Vdc 2,5KHz IP67

S.2429
POWER SUPPLY DIMMABLE DALI2, PUSH DIM 75W 230Vac/24Vdc 3,6KHz IP20

S.2441
POWER SUPPLY DIMMABLE DALI, PUSH DIM, 0-10V, 1-10V 230Vac/24Vdc 24W 244Hz IP20

S.2442
POWER SUPPLY DIMMABLE DALI2, PUSH DIM, 0-10V, 1-10V 230Vac/24Vdc 75W 244Hz IP20

S.2447
POWER SUPPLY DALI 200W 230Vac/24Vdc

Power supply for monochromatic LED 200W 240V/24Vdc The Total power of all connected luminaires may not be higher than the power of the driver. IP67 CLASS II SELV Dimensions 195x68x39mm

S.2449
POWER SUPPLY DIMMABLE DALI2, PUSH DIM 100W 230Vac/24Vdc 3,6KHz IP20

S.9099
Master Interface

Dimmer

S.2476
INTERFACE DALI DT6

The following devices/interfaces are used to control the color, temperature and brightness of the TUNABLE WHITE LED via DALI (DT6 ) signal. These devices need a 24Vdc power supply Not Dimmable ( type S.2405, S.2406, S.2445 and S.2446) and must be placed between the 24Vdc power supply and the luminaires. Therefore choose a 24V power supply based on the maximum power used of the luminaires up to a maximum of 96W. IP67 Operating mode BALANCE & DIM Require remote power supply 230V/24Vdc Dimensions 175,5mmx86,5mmx43mm

S.2477
INTERFACE DALI DT8

The following devices/interfaces are used to control the color, temperature and brightness of the TUNABLE WHITE LED via DALI (DT8 ) signal. These devices need a 24Vdc power supply Not Dimmable ( type S.2405, S.2406, S.2445 and S.2446) and must be placed between the 24Vdc power supply and the luminaires. Therefore choose a 24V power supply based on the maximum power used of the luminaires up to a maximum of 96W. IP67 Operating mode BALANCE & DIM Dimensions 175,5mmx86,5mmx43mm

S.2478
INTERFACE DALI DT6

The following devices/interfaces are used to control the color, temperature and brightness of the TUNABLE WHITE LED via DALI (DT6) signal. These devices need a 24Vdc power supply Not Dimmable ( type S.2405, S.2406, S.2445 and S.2446) and must be placed between the 24Vdc power supply and the luminaires. Therefore choose a 24V power supply based on the maximum power used of the luminaires up to a maximum of 96W. IP20 Operating mode BALANCE & DIM Require remote power supply 230V/24Vdc Dimensions 28mmx14mmx33mm

S.2479
INTERFACE DALI DT8

The following devices/interfaces are used to control the color, temperature and brightness of the TUNABLE WHITE LED via DALI (DT8) signal. These devices need a 24Vdc power supply Not Dimmable ( type S.2405, S.2406, S.2445 and S.2446) and must be placed between the 24Vdc power supply and the luminaires. Therefore choose a 24V power supply based on the maximum power used of the luminaires up to a maximum of 96W. IP20 Operating mode BALANCE & DIM Require remote power supply 230V/24Vdc Dimensions 28mmx14mmx33mm

S.3450
DIMMER DMX IP67

The following devices/interfaces are used to control the color and brightness of the RGBW LED through DMX signal. These devices need a 24Vdc power supply Not Dimmable (type S.2405, S.2406, S.2445 and S.2446) and must be placed between the 24Vdc power supply and the luminaires. Therefore choose a 24V power supply based on the maximum power used of the luminaires up to a maximum of 240W. IP67 Dimensions 255mmx100mmx55mm

S.3451
DIMMER DALI DT6 IP67

The following devices/interfaces are used to control the color and brightness of the RGBW LED through DALI signal. These devices need a 24Vdc power supply Not Dimmable (type S.2405, S.2406, S.2445 and S.2446) and must be placed between the 24Vdc power supply and the luminaires. Therefore choose a 24V power supply based on the maximum power used of the luminaires up to a maximum of 240W. DALI addresses :4 IP67 Dimensions 255mmx100mmx55mm

S.3452
DIMMER BOX DMX IP66 (5x Out)

The following devices/interfaces are used to control the color and brightness of the RGBWW LED through DMX signal. These devices need a 24Vdc power supply Not Dimmable (type S.2405, S.2406, S.2445 and S.2446) and must be placed between the 24Vdc power supply and the luminaires. Therefore choose a 24V power supply based on the maximum power used of the luminaires up to a maximum of 240W. IP66 Dimensions 210mmx200mmx92mm

Led controll

S.3460
DMX512 / RDM LED CONTROLLER

Allows automatic addressing of RGBW products with integrated DMX via the RDM protocol. Once the addressing procedure is complete, this accessory can be removed from the system. IP20 Dimensions 125mmx33mmx20mm

Poles Recessed

S.2800
H 2,5m Ø60mm CYLINDRICAL POLE TO BE BURIED

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 60mm, 3mm in thickness, total length 3,00m, single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,50m: Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

Painting Process: PRE POLYMERIZATION a process of introducing an epoxy primer with excellent characteristics to the paint which also offers very high resistance to oxidation due to its Zinc content. POLYMERIZATION a process with the application of polyester powder with high resistance against UV rays and harsh weather conditions. Resistance test protection for Marine applications for 1500h.

S.2810
H 3,16m Ø102mm CYLINDRICAL POLE TO BE BURIED with Ø76mm SPIGOT

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 102mm, 3mm in thickness, total length 3,77m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,50m : Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2811
H 4,16m Ø102mm CYLINDRICAL POLE TO BE BURIED with Ø76mm SPIGOT

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 102mm, 3mm in thickness, total length 4,77m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,50m : Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2812
H 3,0m Ø76mm CYLINDRICAL POLE TO BE BURIED

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 76mm, 3mm in thickness, total length 3,50m, single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

Including inspection door, terminal cable block and fuse.

S.2814
CYLINDRICAL POLE H 4,5m Ø102mm TO BE BURIED

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 102mm, 3mm in thickness, total length 5,00m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,50m : Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 1m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2815
CYLINDRICAL POLEH 6,44m Ø102mm TO BE BURIED

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 102mm, 4mm in thickness, total length 7,24m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,80m : Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 1m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2816
H 5,16m Ø102mm CYLINDRICAL POLE TO BE BURIED with Ø76mm SPIGOT

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 102mm, 3mm in thickness, total length 5,77m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,50m : Suggested reinforced concrete footstall dimension 1m x 1m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2817
CYLINDRICAL SHAPED POLE H 8,5m Ø 168mm - Ø102mm TO BE BURIED

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 168mm ÷102mm, 4-3mm in thickness, total length 9,3m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,80m : Suggested reinforced concrete footstall dimension 1m x 1m h 1m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2818
H 6,44m Ø102mm CYLINDRICAL POLE TO BE BURIED with Ø76mm SPIGOT

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 102mm, 4mm in thickness, total length 7,35m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2826
H 4,2m Ø120mm CYLINDRICAL POLE TO BE BURIED

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 120mm, 3mm in thickness, total length 4,80m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,60m : Suggested reinforced concrete footstall dimension 0,8m x 0,8m h 0,8m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

Cap COPE2826PVC.09 already installed.

S.2842
H 3,5m Ø60mm CYLINDRICAL POLE TO BE BURIED

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 60mm, 4mm in thickness, total length 4,00m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,50m : Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

S.2844
H 4,5m Ø76mm CYLINDRICAL POLE TO BE BURIED

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 76mm, 4mm in thickness, total length 5,00m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for ground recessed installation to a cement base 0,5m : Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

Poles With flange

S.2801
H 2,5m Ø60mm CYLINDRICAL POLE WITH BASE

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 60mm, 3mm in thickness, total length 2,50m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for installation to a planted root flange through a base plate 250mm x250mm x12mm in steel S355JO : Suggested reinforced concrete footstall dimension 1m x 1m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

S.2805
H 3,0m Ø38mm CYLINDRICAL POLE

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 38mm, 4mm in thickness, total length 3,00m, in aluminium EN AW6060.

Suitable for ground recessed installation to a cement base 0,50m ( Accessory S.2806 ) : Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The surface protection treatment is done through hot dip galvanization.

S.2807
H 3,5m Ø60mm CYLINDRICAL POLE

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 60mm, 4,5mm in thickness, total length 3,50m, in aluminium EN AW6060.

Suitable for ground recessed installation to a cement base 0,50m ( Accessory S.2808 ) : Suggested reinforced concrete footstall dimension 1,0m x 1,0m h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The surface protection treatment is done through hot dip galvanization.

S.2813
H 3,0m Ø76mm CYLINDRICAL POLE WITH BASE

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 76mm, 3mm in thickness, total length 3,00m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2843
H 3,5m Ø60mm CYLINDRICAL POLE WITH BASE

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 60mm, 4mm in thickness, total length 3,50m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for installation to a planted root flange through a base plate in steel S355JO Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

S.2845
H 4,5m Ø76mm CYLINDRICAL POLE WITH BASE

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 76mm, 4mm in thickness, total length 4,50m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for installation to a planted root flange through a base plate in steel S355JO Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

S.2846
H 4,2m Ø120mm CYLINDRICAL POLE WITH BASE

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 120mm, 3mm in thickness, total length 4,20m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

Including inspection door, terminal cable block and fuse.

Cap COPE2826PVC.09 already installed.

S.2848
H 6,0m Ø120mm CYLINDRICAL POLE WITH BASE

Cylindrical shaped poles consisting of: straight circular section shaft, Ø 120mm, 3mm in thickness, total length 6,00m , single section built by using longitudinally welded tubes by induction welding (ERW) UNI EN 10219-2-ISO 4200

Suitable for installation to a planted root flange through a base plate 250x250x12mm in steel S355JO : Suggested reinforced concrete footstall dimension 1x1 h 0,7m. Footstall dimension can be calculated according to your country norms and ground properties.

The grade of steel used is S235JR (Fe360B) with material characteristics as per normative UNI EN 10025;

The surface protection treatment is done through hot dip galvanization.

MINISLOT AVANT-GARDE INSTALLED ON S.2848 POLE:
Finished product total height = 7.13 m

Cap COPE2826PVC.09 already installed.

Pole adaptor

S.1016
FLANGE FOR POLE Ø60mm INSTALLATION

Die-cast aluminium flange suitable only for Ø 60 mm poles. To install the flange on Ø 76mm pole the screws kit SACVITFOCTOWER2 must be purchased separately. The flange can be used for maximum 2 projectors, one for each side.

S.1017
FLANGE FOR POLE Ø76mm INSTALLATION

Die-cast aluminium flange suitable only for Ø76mm poles. The flange can be used for maximum 2 projectors, one for each side.

S.1018
FLANGE FOR POLE Ø102mm INSTALLATION

Die-cast aluminium flange suitable only for Ø 102 mm poles. The flange can be used for maximum 2 projectors, one for each side.

S.1084
FLANGE FOR POLE Ø60mm INSTALLATION

Die-cast aluminium flange suitable only for Ø 60 mm poles. The flange can be used for maximum 2 projectors, one for each side.

S.1085
FLANGE FOR POLE Ø76mm INSTALLATION

Die-cast aluminium flange suitable only for Ø76mm poles. The flange can be used for maximum 2 projectors, one for each side.

S.1107
ANCHOR BASE

Thanks to the special anchor base the luminaire can be fixed to new or existing poles of diameter of 60 mm or 76 mm.

S.1239
FLANGE FOR POLE Ø120mm INSTALLATION

Die-cast aluminium flange suitable only for Ø 120 mm poles. The flange can be used for maximum 2 projectors, one for each side.

S.1657
ANCHOR BASE

Thanks to the special anchor base the luminaire can be fixed to new or existing poles of diameter of 60 mm or 76 mm.

S.1667
ANCHOR BASE

Thanks to the special anchor base the luminaire can be fixed to new or existing poles of diameter of 60 mm or 76 mm.

S.1758
FLANGE FOR POLE 60/76mm INSTALLATION

Die-cast aluminium flange suitable only for Ø60mm/ Ø76mm poles.

S.3019
ANCHOR BASE

Thanks to the special anchor base the luminaire can be fixed to new or existing poles of diameter of no less than 60 mm.

S.3044
ACCESSORY SINGLE MOUNT POLE Ø60 and Ø76mm

S.3045
ACCESSORY DOUBLE MOUNT POLE Ø60 and Ø76mm

S.3046
ACCESSORY SINGLE MOUNT POLE Ø60mm

S.3047
ACCESSORY DOUBLE MOUNT POLE Ø60mm

S.3069
ANCHOR BASE

Thanks to the special anchor base the luminaire can be fixed to new or existing poles of diameter of no less than 60 mm.

Planted root for poles

S.0908
ANCHORING FLANGE for AIR-LIGHTING POLE

Anchoring base Height 1600 mm (H 800 mm above ground) to be buried in concrete. Footstall dimension can be calculated according to your country norms and ground properties.

S.0909
BASE FOR SUPPORT AND COUNTERWEIGHT CONTAINER for AIR-LIGHTING POLE

diam. 350mm, H 600mm To ensure stability in the absence of ground fixings, the container must hold two sandbags, each weighing 25 kg. The container can house the remote power supply.

S.1468
FIXING BASE FOR MINISHIFT POLE

Base 300x300mm Spacing 200x200mm Holes for Ø18mm

S.1469
ANCHORING BASE FOR MINISHIFT POLE

Anchoring base to be buried in concrete. Footstall dimension can be calculated according to your country norms and ground properties.

S.1488
FIXING BASE FOR SHIFT PRO POLE

Base 300x300mm Spacing 200x200mm Holes for Ø18mm

S.1489
ANCHORING BASE FOR SHIFT PRO POLE

Anchoring base to be buried in concrete. Footstall dimension can be calculated according to your country norms and ground properties.

S.2806
FLANGE FOR POLE S.2805

Flange to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.2808
FLANGE FOR POLE S.2807

Flange to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.2840
PLANTED ROOT for CYLINDRICAL POLE S.2846, S.2848

h = 550 mm and bolts in galvanized steel with M16 threads. Suggested reinforced concrete footstall dimension:
A = 0.7 m
B = 1 m

Footstall dimension can be calculated according to your country norms and ground properties.

S.2849
PLANTED ROOT for CYLINDRICAL POLE S.2801, S.2813, S.2843, S.2845

C= 200mm, D=200mm E=Ø80mm, h=460mm, h1=90mm and bolts in galvanized steel with M16 threads. Suggested reinforced concrete footstall dimension **: A = 0.7 m B = 0.7 m
**Footstall dimension can be calculated according to your country norms and ground properties.

Pole base cover

S.2809
POLE BASE COVER

For pole with base and pole to be buried Ø102mm or Ø120mm. Die-cast aluminium housing.

Base for surface application

C.8054
Fixing base for surface applications

Concrete Wall, through the use of the fixing base, becomes a surface fitting

Planted root

S.1508
ACCESSORY FOR VERTICAL INSTALLATION

Plate for vertical installation of the MicroKeen projector on concrete/tiled floors. For installations on grassy/paved ground the use of the S.1004 Spike is required.

S.1509
ACCESSORY FOR VERTICAL INSTALLATION

Plate for vertical installation of the MiniKeen projector on concrete/tiled floors. For installations on grassy/paved ground the use of the S.1004 Spike is required.

S.1519
ACCESSORY FOR VERTICAL INSTALLATION

Plate for vertical installation of the Keen projector on concrete/tiled floors. For installations on grassy/paved ground the use of the S.1014 Spike is required.

S.2009
FLANGE

Ø 150 mm h 600mm flange to be fixed in concrete with stainless steel screws for fixing in the ground.

S.2099
FLANGE

Flange Ø 76mm h 165mm to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.2119
FLANGE

Flange Ø 248mm h 235mm to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.2148
FLANGE

Flange Ø 102mm to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.2307
90° JUNCTION ACCESSORY FOR SINGLE FLAT SURFACES

All surface mounted versions may be connected to create luminous angles at 90° in relation to a single installation plan (wall or ceiling) with the specific accessories.

S.2308
90° JUNCTION ACCESSORY FOR PERPENDICULAR SURFACES

Luminous angles at 90° on two perpendicular surfaces (ceiling/wall or wall/wall) can be achieved as well. Also in this case specific accessories are needed.

S.3159
FLANGE FOR BOLLARD

Flange to be fixed in concrete with stainless steel screws for fixing in the ground.

S.3671
FLANGE

Fixation base plate installation. Kg 1,5

S.3672
FLANGE

Fixation base plate installation. Kg 3,5

S.4009
FLANGE

Ø 150 mm h 600mm flange to be fixed in concrete with stainless steel screws for fixing in the ground.

S.4129
FLANGE

Ø 195 mm h 800mm flange to be fixed in concrete with stainless steel screws for fixing in the ground.

S.4171
FLANGE

Flange Ø 195mm h 165mm to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.4172
FLANGE

Flange Ø 140mm h 115mm to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.4663
FLANGE FOR GROUND APPLICATION BOLLARD

Flange 77mm x 58mm h 170mm to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.5200
FLANGE FOR GROUND APPLICATION

Flange Ø 190mm h 225mm to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.5301
FLANGE FOR GROUND APPLICATION

Flange Ø 130mm h 155mm to be fixed in concrete with stainless steel screws for fixing in the ground. Footstall dimension can be calculated according to your country norms and ground properties.

S.5310
FLANGE

Ø 180 mm flange to be fixed in concrete with stainless steel screws for fixing in the ground.

S.5350
FLANGE FOR BOLLARD

Ø 240 mm flange to be fixed in concrete with stainless steel screws for fixing in the ground.

S.5680
ANCHOR FLANGE TO BE CEMENTED TO THE GROUND

For applications in driveways areas, the luminaires must be installed with its proper anchor flange. The flange is provided with the necessary fixing A4 screws in stainless steel.

S.5690
ANCHOR FLANGE TO BE CEMENTED TO THE GROUND

For applications in driveways areas, the luminaires must be installed with its proper anchor flange. The flange is provided with the necessary fixing A4 screws in stainless steel.

S.5699
ANCHOR FLANGE TO BE CEMENTED TO THE GROUND

For applications in driveways areas, the luminaires must be installed with its proper anchor flange. The flange is provided with the necessary fixing A4 screws in stainless steel.

S.6309
FLANGE FOR BOLLARD

Ø 120 mm flange to be fixed in concrete with stainless steel screws for fixing in the ground.

S.6359
FLANGE

Steel flange with stainless steel screws (to be fixed in concrete).

S.7108
FIXING BASE FOR PARK RECTANGULAR POLE

Base 300x300mm Spacing 200x200mm Holes for M16

S.7109
FLANGE ACCESSORY

100x150mm h 820mm flange to be fixed in concrete with stainless steel screws for fixing in the ground.

S.7219
FLANGE

Steel flange with stainless steel screws (to be fixed in concrete).

S.7249
FLANGE

Steel flange with stainless steel screws (to be fixed in concrete).

S.7269
FLANGE

Steel flange with stainless steel screws (to be fixed in concrete).

S.7284
FLANGE

Steel flange with stainless steel screws (to be fixed in concrete).

S.7288
FLANGE

Steel flange with stainless steel screws (to be fixed in concrete).

S.7289
FLANGE

Steel flange with stainless steel screws (to be fixed in concrete).

Stake

S.1004
STAKE

In POLYPROPYLENE. Colour: black (code .09)

S.1005
STAKE

In POLYPROPYLENE. Colour: black (code .09)

S.1014
GROUND STAKE

In POLYPROPYLENE.
Colour: black (code .09)

S.1309
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length = 350 mm

S.1319
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length = 430 mm

S.1609
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length = 210 mm

S.1659
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length = 300 mm

S.1768
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length =300 mm

S.2088
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length = 300 mm

S.2098
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length = 270 mm

S.2519
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length = 193 mm

S.2776
STAKE

In polypropylene Colour: black (code .09)

S.3049
STAKE

In polypropylene Colour: black (code .09)

S.3079
STAKE

In polypropylene Colour: black (code .09)

S.3524
STAKE

In POLYPROPYLENE.
Colour: black (code 09)
Length = 270 mm

S.3554
STAKE IN POLYPROPYLENE

Colour: black (code 09)
Total length = 420 mm

Visor

S.1002
VISOR

Colour: black (code 09)

S.1022
VISOR

Colour: black (code 09).

S.1032
VISOR

Colour: black (code 09).

S.1042
VISOR

Colour: black (code 09).

S.1109
ANTIGLARE VISOR

Colour: black (code 09)

S.1308
VISOR

In aluminium Colour: black (code 09)

S.1318
VISOR

In aluminium Colour: black (code 09)

S.1328
VISOR

In aluminium Colour: black (code 09)

S.1368
VISOR

In aluminium Colour: black (code 09)

S.1608
ANTIGLARE VISOR

Colour: black (code 09)

S.1628
ANTIGLARE VISOR

Colour: black (code 09)

S.1658
ANTIGLARE VISOR

Colour: black (code 09)

S.1668
ANTIGLARE VISOR

Colour: black (code 09)

S.2159
VISOR

In aluminium Colour: black (code 09)

S.2169
VISOR

In aluminium Colour: black (code 09)

S.2179
VISOR

In aluminium Colour: black (code 09)

S.2717
VISOR

In aluminium Colour: black (code 09)

S.2718
SNOOT

In aluminium Colour: black (code 09)

S.2719
HONEYCOMB

In aluminium Colour: black (code 09)

S.2737
VISOR

In aluminium Colour: black (code 09)

S.2738
SNOOT

In aluminium Colour: black (code 09)

S.2739
HONEYCOMB

In aluminium Colour: black (code 09)

S.2757
VISOR

In aluminium Colour: black (code 09)

S.2758
SNOOT

In aluminium Colour: black (code 09)

S.2759
HONEYCOMB

In aluminium Colour: black (code 09)

S.2777
VISOR

In aluminium Colour: black (code 09)

S.2778
SNOOT

In aluminium Colour: black (code 09)

S.2779
HONEYCOMB

In aluminium Colour: black (code 09)

S.6159
ANTIGLARE SHIELD

S.6169
ANTIGLARE SHIELD

S.7049
ASYMMETRIC SHIELD

Aluminium shield to be mounted when an asymmetric light distribution is required from the MINIPOSTER pole top.

S.7059
ASYMMETRIC SHIELD

Aluminium shield to be mounted when an asymmetric light distribution is required from the POSTER pole top.

Lenses

S.1752
NARROW BEAM FILTER 10° for PIVOT 4LED

Suitable for PIVOT 4LED 850mA To install inside the fitting.

S.1753
LARGE BEAM FILTER 60° for PIVOT 4LED

Suitable for PIVOT 4LED 850mA To install inside the fitting.

S.1754
ELLIPTICAL BEAM FILTER 60°x10° for PIVOT 4LED

Suitable for PIVOT 4LED 850mA To install inside the fitting.

S.1762
NARROW BEAM FILTER 10° for PIVOT 7LED

Suitable for PIVOT 7LED 230V / 850mA To install inside the fitting.

S.1763
LARGE BEAM FILTER 60° for PIVOT 7LED

Suitable for PIVOT 7LED 230V / 850mA To install inside the fitting.

S.1764
ELLIPTICAL BEAM FILTER 60°x10° for PIVOT 7LED

Suitable for PIVOT 7LED 230V / 850mA To install inside the fitting.

S.1772
NARROW BEAM FILTER 10° for PIVOT 12LED

Suitable for PIVOT 12LED 230V / 850mA To install inside the fitting.

S.1773
LARGE BEAM FILTER 60° for PIVOT 12LED

Suitable for PIVOT 12LED 230V / 850mA To install inside the fitting.

S.1774
ELLIPTICAL BEAM FILTER 60°x10° for PIVOT 12LED

Suitable for PIVOT 12LED 230V / 850mA To install inside the fitting.

S.2605
NARROW BEAM FILTER 10° for BETWEEN 4LED

Suitable for BETWEEN 4LED and 2x4LED. To install inside the fitting.

S.2606
LARGE BEAM FILTER 60° for BETWEEN 4LED

Suitable for BETWEEN 4LED and 2x4LED. To install inside the fitting.

S.2607
ELLIPTICAL BEAM FILTER 60°x10° for BETWEEN 4LED

Suitable for BETWEEN 4LED and 2x4LED. To install inside the fitting.

S.2615
NARROW BEAM FILTER 10° for BETWEEN 7LED

Suitable for BETWEEN 7LED and 2x7LED. To install inside the fitting.

S.2616
LARGE BEAM FILTER 60° for BETWEEN 7LED

Suitable for BETWEEN 7LED and 2x7LED. To install inside the fitting.

S.2617
ELLIPTICAL BEAM FILTER 60°x10° for BETWEEN 7LED

Suitable for BETWEEN 7LED and 2x7LED. To install inside the fitting.

S.2710
MEDIUM BEAM FILTER 30° for MINIPOINTER

Suitable for MINIPOINTER To install inside the fitting.

S.2711
LARGE BEAM FILTER 60° for MINIPOINTER

Suitable for MINIPOINTER To install inside the fitting.

S.2712
ELLIPTICAL BEAM FILTER 60°x10° for MINIPOINTER

Suitable for MINIPOINTER To install inside the fitting.

S.2730
MEDIUM BEAM FILTER 30° for POINTER

Suitable for POINTER To install inside the fitting.

S.2731
LARGE BEAM FILTER 60° for POINTER

Suitable forPOINTER To install inside the fitting.

S.2732
ELLIPTICAL BEAM FILTER 60°x10° for POINTER

Suitable for POINTER To install inside the fitting.

S.2750
MEDIUM BEAM FILTER 30° for MEGAPOINTER

Suitable for MEGAPOINTER To install inside the fitting.

S.2751
LARGE BEAM FILTER 60° for MEGAPOINTER

Suitable for MEGAPOINTER To install inside the fitting.

S.2752
ELLIPTICAL BEAM FILTER 60°x10° for MEGAPOINTER

Suitable for MEGAPOINTER To install inside the fitting.

S.2770
MEDIUM BEAM FILTER 30° for MICROPOINTER

Suitable for MICROPOINTER To install inside the fitting.

S.2771
LARGE BEAM FILTER 60° for MICROPOINTER

Suitable for MICROPOINTER To install inside the fitting.

S.2772
ELLIPTICAL BEAM FILTER 60°x10° for MICROPOINTER

Suitable for MICROPOINTER To install inside the fitting.

S.9095
Black shielding diffuser for 1,0m version of the lighting rod Highlighter

Black polycarbonate diffuser must be carefully cut by the installer with a circular saw where plug-in products will be installed. Highlighter off, with polycarbonate black diffuser. The polycarbonate black diffuser is a screening element. When Highlighter is off, the black diffuser turns the silicone strip into black. Highlighter on, with polycarbonate black diffuser. The polycarbonate black diffuser is a screening element. When Highlighter is on, the polycarbonate diffuser would turns into light grey and the light emitted will be of around 50%.

S.9096
Black shielding diffuser for 2,0m version of the lighting rod Highlighter

S.9097
Black shielding diffuser for 3,0m version of the lighting rod Highlighter

Connectors

S.3670
1 ADDITIONAL CABLE GLAND

Required for the connection of over 2 luminaires to the junction box S.3660 / power supply S.3664, S.3665, S.3667, S.3668.

S.5504
3 WAY CONNECTOR

For cables up to 3x1,5mm² diam. Min 7,0mm / Max 12mm IP68 Dimensions: 80 x 54 x 24 mm

S.5506
4 WAY GEL CONNECTOR

For cables up to 3x2,5mm² diam. Min 6,5mm / Max 12mm IP68 Dimensions: 105 x 44 x 24 mm

S.5507
3 WAY GEL CONNECTOR

For cables up to 5x1,5mm² diam. Min 6,5mm / Max 12mm IP68 Dimensions: 90 x 43 x 30 mm

S.5519
4 WAY GEL CONNECTOR

For cables up to 4x1,5mm² diam. Min 6,5mm / Max 12mm IP68 Dimensions: 105 x 44 x 24 mm

S.5529
1 WAY GEL CONNECTOR

For round cables up to 3x1.5 mm², diameter min. 5.5 mm / max. 10 mm For flat cables 2x3 mm IP68 Dimensions: diameter 23 mm, length 70 mm

Other

C.8033
Drilling jig for shutter

The template for drilling facilitates the alignment of the recessed profile of Ghost Continuous Line. You require only one template for each size which can be used. again.

C.8035
Drilling jig for shutter

The template for drilling facilitates the alignment of the recessed profile of Ghost Continuous Line. You require only one template for each size which can be used. again.

C.8037
Drilling jig for shutter

The template for drilling facilitates the alignment of the recessed profile of Ghost Continuous Line. You require only one template for each size which can be used. again.

C.8039
Drilling jig for shutter

The template for drilling facilitates the alignment of the recessed profile of Ghost Continuous Line. You require only one template for each size which can be used. again.

S.1108
STRAP FOR APPLICATIONS ON TREES

Black strap, length 40 cm.

S.1607
STRAP FOR APPLICATIONS ON TREES

Black strap, length 2m..

Joining connectors

S.9080
Ceiling Rose

The painted aluminium ceiling rose accessory is useful for masonry installations that need to hide the electric corrugated. The accessory is composed by two ceiling roses.

S.9090
Corner juntion

JUNTIONS FOR HIGHLIGHTER SURFACE In painted steel

S.9091
Linear juntion

JUNTIONS FOR HIGHLIGHTER SURFACE In painted steel

Additional heads

S.1465H
MINISHIFT ADDITIONAL HEAD WITH 16° OPTIC

LED MODULE 2700K CRI90 1291lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1465N
MINISHIFT ADDITIONAL HEAD WITH 16° OPTIC

LED MODULE 4000K CRI80 1650lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1465W
MINISHIFT ADDITIONAL HEAD WITH 16° OPTIC

LED MODULE 3000K CRI90 1363lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1466H
MINISHIFT ADDITIONAL HEAD WITH 51° OPTIC

LED MODULE 2700K CRI90 1291lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1466N
MINISHIFT ADDITIONAL HEAD WITH 51° OPTIC

LED MODULE 4000K CRI80 1650lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1466W
MINISHIFT ADDITIONAL HEAD WITH 51° OPTIC

LED MODULE 3000K CRI90 1363lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1467H
MINISHIFT ADDITIONAL HEAD WITH ELLIPTIC OPTIC

LED MODULE 2700K CRI90 1291lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1467N
MINISHIFT ADDITIONAL HEAD WITH ELLIPTIC OPTIC

LED MODULE 4000K CRI80 1650lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1467W
MINISHIFT ADDITIONAL HEAD WITH ELLIPTIC OPTIC

LED MODULE 3000K CRI90 1363lm 14,7W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1490H
SHIFT PRO ADDITIONAL HEAD WITH 19° OPTIC

LED MODULE 2700K CRI90 4018lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1490N
SHIFT PRO ADDITIONAL HEAD WITH 19° OPTIC

LED MODULE 4000K CRI80 4292lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1490W
SHIFT PRO ADDITIONAL HEAD WITH 19° OPTIC

LED MODULE 3000K CRI90 4240lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1491H
SHIFT PRO ADDITIONAL HEAD WITH 38° OPTIC

LED MODULE 2700K CRI90 4018lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1491N
SHIFT PRO ADDITIONAL HEAD WITH 38° OPTIC

LED MODULE 4000K CRI80 4292lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1491W
SHIFT PRO ADDITIONAL HEAD WITH 38° OPTIC

LED MODULE 3000K CRI90 4240lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1492H
SHIFT PRO ADDITIONAL HEAD WITH ELLIPTIC OPTIC

LED MODULE 2700K CRI90 4018lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1492N
SHIFT PRO ADDITIONAL HEAD WITH ELLIPTIC OPTIC

LED MODULE 4000K CRI80 4292lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1492W
SHIFT PRO ADDITIONAL HEAD WITH ELLIPTIC OPTIC

LED MODULE 3000K CRI90 4240lm 27W 220V-240Vac 50/60Hz Dimmable DALI 2 / PUSH IK10

S.1496
SHIFT PRO TOP HEAD READY FOR WI-FI ACCESS POINT

Designed for Wi-Fi network Access Point. The head features a compartment diameter 110mm and Height 400mm, intended to accommodate commercially available Wi-Fi devices. Devices and Antennas not included

S.1497
SHIFT PRO IP65 DOOR WITH SCHÜKO ELECTRICAL PLUG

Hatch IP65 and with an integrated electrical plug type SCHÜKO to power electronic devices in the outdoor. Class I, IK06, Wmax 3500W Available upon request with European electrical sockets.

S.1498
SHIFT PRO ADDITIONAL HEAD WITH CAMERA

Passive IP67 camera, 4 MP with fixed 2.8mm lens IR up to 30 meters, PoE ONVIF protocol compatible

S.1499
SHIFT PRO ADDITIONAL HEAD WITH SPEAKER

Rated power input 10W Maximum power input 20W Nominale impedence 8Ohm Nominal Voltage 100V Sensitivity 1W/1m 87 dB Frequency response 100-20K Hz IP 65